Tall primo bottle issue? Getting last bit of oil out

[prototype5]

So i have a weird issue with the stopper. Iv never had this before on a bottle. The bottom of the stopper hangs down low... and its solid all the way around, so the oil can't flow throw the middle.

Im down to the last bit of oil, probably between 1-2ml. But when i put the needle in, the oil goes around the stopper. Theres no way to get the remaining oil out. The oil goes around the stopper and never makes it to the middle. Iv tried laying it on its side too and I just can't get any.

Normally I would care and just toss it, but with promo being almost $200 a bottle, I rather not waste any.

Any tips or hints? Usually the stopper isnt solid all the way around and the oil can flow through it to the middle. Both of my primo bottles are like this.

 

[Big_Jimmy434]

I draw with an 18ga and i usually tilt the vial on its side and then just draw it up. 18ga is like a vacuum cleaner.

 

[zwhit]

Cut the top and pull it and the stopper off. Doesn't take much to get through. I'm not leaving almost a half cc of even test in my vials

 

[BFulforth]

So i have a weird issue with the stopper. Iv never had this before on a bottle. The bottom of the stopper hangs down low... and its solid all the way around, so the oil can't flow throw the middle.

Im down to the last bit of oil, probably between 1-2ml. But when i put the needle in, the oil goes around the stopper. Theres no way to get the remaining oil out. The oil goes around the stopper and never makes it to the middle. Iv tried laying it on its side too and I just can't get any.

Normally I would care and just toss it, but with promo being almost $200 a bottle, I rather not waste any.

Any tips or hints? Usually the stopper isnt solid all the way around and the oil can flow through it to the middle. Both of my primo bottles are like this.

Can you like stab through on an angle on one of those indents close to the side?


Sent from my iPhone using Tapatalk

 

[HFO4]

That stopper sucks if you have a lot of those you can get a box of 100 1.5” 20g for $20 more or less

 

[Veneficus]

A bottle opener can work too but they also make vial cap removers which look a lot like bottle openers.
Or however you do it take the cap off and draw it all out that way. I'd make sure there's not air blowing around so you don't get hair or particles in it. Or you can get a syringe filter and use that when you inject to make extra sure you're not injecting solid particles. But there's probably low risk of that anyways. Just pop it off, draw really fast and pin it.

 

[Vee]

I HATE those stoppers!! Total boner killers

 

[zwhit]

A bottle opener can work too but they also make vial cap removers which look a lot like bottle openers.
Or however you do it take the cap off and draw it all out that way. I'd make sure there's not air blowing around so you don't get hair or particles in it. Or you can get a syringe filter and use that when you inject to make extra sure you're not injecting solid particles. But there's probably low risk of that anyways. Just pop it off, draw really fast and pin it.

No different than using amps. Just don't leave it sitting around and draw it out immediately after opening it and I've never had an issue and used hundreds of amps over the years, if not more

 

[Lustyscripps]

Just rip the top of the vial off with pliers. 1 inch 25ga reaches the bottom. Tilt it and draw everything out. Never waste a drop

 

[Vee]

Just rip the top of the vial off with pliers. 1 inch 25ga reaches the bottom. Tilt it and draw everything out. Never waste a drop

Thats my “go-to” move with those stoppers lol

 

[MrWhisper]

Just rip the top of the vial off with pliers. 1 inch 25ga reaches the bottom. Tilt it and draw everything out. Never waste a drop

This

Been there done that.

 

[Durro NoHurtNoBigShirt]

Can you like stab through on an angle on one of those indents close to the side?


Sent from my iPhone using Tapatalk

That’s what I had to do with these. You have to stab through the rubber at the indentation at an angle and you should get it all out. It’ll take a few tries and you’re gonna have to obviously replace the needle use a different needle to inject.

 

[Astro95]

Remove the stopper man…. The vial is not sealed shut. Bust the crimp and remove the stopper then go in with an 18,20g vial up right and slurp it all up.

 

[gsuprem3]

Get a longer needle…

 

[Bolan]

I use a pair of needle nose pliers and pop the crimp/stopper off.

I do this when I've kicked a vial, peel the label off and pry the crimp and stopper off... wrap in a paper towel and smash it with a hammer to crush it.
I'm not paranoid or nothing........

I can also see where the oil would drop into the sides like that, that's a fucked up stopper. A longer needle wouldn't even get to it unless you drive the needle all the way through the thick part of the stopper.