• 👋Hello, please SIGN-UP FOR A FREE account and become a member of our community!
    You will then be able to start threads, post comments and send messages to other members. Thanks!
  • 💪Check Out IronMag Labs Andro Hard® - Powered by R-Andro & Epi-Andro! 💊
  • 👉Check Out Platinum Pharms🌽Corn Hole Sale!🌽

Test 400

Rickster41

Rickster41

Registered User
Registered
Joined
Sep 3, 2015
Messages
679
Reaction score
23
Points
18
Get Shredded!
Anyone have trouble getting test 400 to flow through a 25g pin? I have no trouble with the normal 250 mg test. Just wondering if this is normal since it's the first time I've used a concentration that high. I should mention this is crashed gear that I have to heat up every use. Once it's in there is no pip or swelling or anything

Sent from my SM-G975U using Tapatalk
 
Depends on carrier - a one ml syringe provides more psig. , so if you were using a 3ml barrel , a switch could help. Otherwise a 22 or 23 could help.

Max
 
maxmuscle1 said:
Depends on carrier - a one ml syringe provides more psig. , so if you were using a 3ml barrel , a switch could help. Otherwise a 22 or 23 could help.

Max
Click to expand...
I do use a 3ml barrel, I might have to try the smaller one or just save the 400 in an emergency stash

Sent from my SM-G975U using Tapatalk
 
Rickster41 said:
I do use a 3ml barrel, I might have to try the smaller one or just save the 400 in an emergency stash

Sent from my SM-G975U using Tapatalk
Click to expand...

Oils push through a one ml more smoothly (totally different experience)

 
zionoir626 said:
I'll have to give that a try...
Click to expand...

Definitely. Learned during internship with pain mgmt doc . He did 100’s of injection procedures a week and depending on steroid/anesthetic/pain drug he was injecting(also letting me) ; there was a huge difference in (psig) the amount of pressure needed depending on the compound and gauge of needle . A 5 or 3ml was super hard to push through a 25g and we would get a 1ml luer Lock and transfer (combo), with needle still in place, it would push through easily . So I use the technique myself .

Max
 
Yeah..but I seldom do just 1cc..
But I'll get some and try..plus my girl is dying to get back on the infamous cut stack
She loves the Tren

- - - Updated - - -

I think this time I'm signing her up with Dollar Shave Club..
 
zionoir626 said:
Yeah..but I seldom do just 1cc..
But I'll get some and try..plus my girl is dying to get back on the infamous cut stack
She loves the Tren

- - - Updated - - -

I think this time I'm signing her up with Dollar Shave Club..
Click to expand...

Yeah. I like 3ml for volume , but sometimes (if doing high mg combos of separate vials) it can work very well. A little of this , a little of that ..


Max
 
Rickster41 said:
Anyone have trouble getting test 400 to flow through a 25g pin? I have no trouble with the normal 250 mg test. Just wondering if this is normal since it's the first time I've used a concentration that high. I should mention this is crashed gear that I have to heat up every use. Once it's in there is no pip or swelling or anything

Sent from my SM-G975U using Tapatalk
Click to expand...
Most blends will be thick. After you fill the barrel and switch out the tip, place cap back on and heat that bad boy with a blow drier.. If you withdrawal say 1mL, pull the plunger back to the 3mL mark, leaving 2 mL of air, hit it with the blow drier and tilt back and forth every so often like a bubble in a level, back and forth.. I than hold the barrel to the cheek of my face for a sec to see how hot it is to make sure it's not to roasty toasty. From there it should be easier to shoot into the site of your choice.
 
Last edited:
IML Gear Cream!
I've used T400 and 500 and use slin pins for everything, haven't stuck anything bigger than a 29g in years
 
Vis is watching Hair Spray in the bathroom warming his liquid Viagra..
You're not fooling anyone...bald guys don't use hair dryers..
 
Question for you....

If this is gear you have to heat up everytime because it's crashed why are you using it?
Also how long does it take to crash again sitting in the bottle?

I've never had test e 400 crash on me but I also brew with mct
 
zionoir626 said:
Vis is watching Hair Spray in the bathroom warming his liquid Viagra..
You're not fooling anyone...bald guys don't use hair dryers..
Click to expand...

Hey man, the blow dryer hardens the hairspray when I do the comb over.. it gives it that hard crisp shell.. shit doesn't move..:roflmao:
 
I knew there was more to it..
My girl has been begging to get back on that cut mix...Test/Tren/Mast
Guess I'll sign her up with Dollar Shave Club
 
Rickster41 said:
Anyone have trouble getting test 400 to flow through a 25g pin? I have no trouble with the normal 250 mg test. Just wondering if this is normal since it's the first time I've used a concentration that high. I should mention this is crashed gear that I have to heat up every use. Once it's in there is no pip or swelling or anything

Sent from my SM-G975U using Tapatalk
Click to expand...

I use test 400 from euro pharmacies and goes easy on 27g needle . Depends on the oil used by each lab .
 
maxmuscle1 said:
Depends on carrier - a one ml syringe provides more psig. , so if you were using a 3ml barrel , a switch could help. Otherwise a 22 or 23 could help.

Max
Click to expand...
definitely the oil used, the script test I get is thick like syrup, I prefer UGL just for this reason, I can pin with slin needles
 
heckler7 said:
definitely the oil used, the script test I get is thick like syrup, I prefer UGL just for this reason, I can pin with slin needles
Click to expand...

This.. I prefer the generic test cyp that I have over my Rx... I use both, but I like the clear mtc oil over the grapeseed that is thick ASF
 
Vision said:
This.. I prefer the generic test cyp that I have over my Rx... I use both, but I like the clear mtc oil over the grapeseed that is thick ASF
Click to expand...

For sure i have testoviron bayer from my pharmacy but the oil is so tick i prefer to use PSL test E or test 400 gold line
 
Back
Top