Results 1 to 4 of 4

Thread: Winstrol

  1. #1
    Senior Member
    boyou boy's Avatar

    Join Date
    Sep 2014

    Thanks Thanks Given 
    Thanks Thanks Received 
    Thanked in
    30 Posts
    Rep Points


    Hey brothers I'm in need of some help. I'm still trying to figure out how to brew injectable winnie. If anyone has mastered brewing winnie I need some help lol.. im willing to give anyone's recipe a shot. It can be water based or oil based. I'm just looking for a easy recipe that really works easily.

    I just tried to brew a small batch of winnie in oil and I'm positive I can toss it out as I think I overheated. It crashed twice so put some serious heat on it but I think I over done it lol...

    Made 20ml I used

    17ml e.o. as Carrier
    Ba at 1%
    The rest was Guaicol as my solvent
    Here's a pic

  2. #2
    Senior Member

    Join Date
    Aug 2013

    Thanks Thanks Given 
    Thanks Thanks Received 
    Thanked in
    10 Posts
    Rep Points

    I did a quick search and found this recipe. I have not tried it myself.
    Good luck.


    Note: there is a tendency to ruin the product during conversion so only use one gram at a time

    Powder: 1 gram
    Produces: 20 ml at 50 mg/ml


    • 1 gram of winstrol
    • one 20 ml glass vial or larger
    • one 20 ml sterile glass vial or larger
    • one 0.45 Whatman sterile syringe filter
    • two 5 or 10 ml syringes
    • two 3 ml syringes
    • three 18 or 20 gauge pins
    • two 22 gauge pins
    • 17 ml of sesame seed oil
    • 0.2 ml of benzyl alcohol
    • 2 ml of Mr.T super solvent


    • measure one gram of powder
    • draw out 2 ml of the Mr. T super solvent using one of the 3 ml syringes
    • place the measured powder in the open vial and add the solvent
    • place the rubber stopper back on the vial and put one of the 20 gauge pins in the stopper
    • place the vial in a small pan and place the pan on the eye of the stove
    • heat until the powder dissolves into a liquid (usually around 239.8-242 degrees F)
    • turn off the heat and let it cool down in the pan to room temperature (approx. 15 minutes)
    • heat the oil in a suitable container in the oven until it reaches a minimum of 212 degrees F to sterilise it (it will be necessary to use slightly more oil than is required as all of it will not be able to be utilised)
    • draw out 0.2 ml of benzyl alcohol (this will account for 1% of the solution so make sure the measurement is correct)
    • add the benzyl alcohol to the solution in the vial and shake very gently
    • draw out the oil with the 10 ml syringe (make sure the oil has cooled down somewhat before doing this)
    • add 15 ml of the oil (saving 2 ml for later) to the solution in the vial and shake very gently Note: If the winstrol begins to clump back up, reheat the solution (place in a pan, put the pan on the eye of the stove and heat until it liquefies again) and allow it to cool down slowly
    • place one of the 18 gauge pins in the sterile, unopened vial and attach the Whatman sterile filter
    • draw out the solution using the other 10 ml syringe, attach to the filter, and slowly press the solution out into the sterile vial
    • use the previously saved 2 ml of oil in the other syringe and run it through the filter to ensure that all the Winstrol passes through
    • after the filtering process, leave the pin in the sterile vial and remove the filter
    • place the vial in a pan and place the pan on the eye of the stove
    • heat for 15-20 minutes, remove from heat, and let it cool down to room temperature (approx. 15 minutes)

    The finished solution will be light-gold in colour.
    Ensure that you follow the guidelines carefully for this conversion.

  3. #3
    IunitsU's Avatar

    Join Date
    Aug 2018

    Thanks Thanks Given 
    Thanks Thanks Received 
    Thanked in
    7 Posts
    Rep Points

    Injectable winstrol is strong stuff if made properly. I prefer injectable over oral but only use oral! Its good either way.

  4. #4
    Board Rep
    ALLEX's Avatar

    Join Date
    Dec 2017

    Thanks Thanks Given 
    Thanks Thanks Received 
    Thanked in
    355 Posts
    Rep Points

    Try 1g of powder and 2.5ml of guaiacol. Add heat until starts smoking. Add castor oil in small amounts bringing to smoke each time. Doesn't really need BA but you can do 1%.

Similar Threads

  1. Winstrol Oil vs Winstrol Water Base
    By gabulldog in forum Anabolic Steroids
    Replies: 5
    Last Post: 08-11-2017, 10:17 PM
  2. Winstrol
    By VTX in forum Anabolic Steroids
    Replies: 9
    Last Post: 06-13-2016, 03:38 AM
  3. winstrol
    By smokedout in forum Anabolic Steroids
    Replies: 11
    Last Post: 02-28-2014, 11:30 PM
  4. Ok guys winstrol dilemna HOW TO MAKE LIQUID WINSTROL
    By tehbeastaxl in forum Research & Homebrew Chemistry
    Replies: 1
    Last Post: 11-02-2013, 05:42 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Copyright© 2012-2019 Anabolic Steroid Forums