Winstrol

Results 1 to 4 of 4

Thread: Winstrol

  1. #1
    Senior Member
    boyou boy's Avatar


    Join Date
    Sep 2014
    Age
    34
    Posts
    1,090

    Thanks Thanks Given 
    23
    Thanks Thanks Received 
    36
    Thanked in
    22 Posts
    Rep Points
    2147483647

    Winstrol

    Hey brothers I'm in need of some help. I'm still trying to figure out how to brew injectable winnie. If anyone has mastered brewing winnie I need some help lol.. im willing to give anyone's recipe a shot. It can be water based or oil based. I'm just looking for a easy recipe that really works easily.

    I just tried to brew a small batch of winnie in oil and I'm positive I can toss it out as I think I overheated. It crashed twice so put some serious heat on it but I think I over done it lol...

    Made 20ml I used

    17ml e.o. as Carrier
    Ba at 1%
    The rest was Guaicol as my solvent
    Here's a pic

  2. #2
    Member


    Join Date
    Aug 2013
    Posts
    58

    Thanks Thanks Given 
    7
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts
    Rep Points
    841822768

    I did a quick search and found this recipe. I have not tried it myself.
    Good luck.

    Winstrol

    Note: there is a tendency to ruin the product during conversion so only use one gram at a time

    Powder: 1 gram
    Produces: 20 ml at 50 mg/ml

    Requirements:


    • 1 gram of winstrol
    • one 20 ml glass vial or larger
    • one 20 ml sterile glass vial or larger
    • one 0.45 Whatman sterile syringe filter
    • two 5 or 10 ml syringes
    • two 3 ml syringes
    • three 18 or 20 gauge pins
    • two 22 gauge pins
    • 17 ml of sesame seed oil
    • 0.2 ml of benzyl alcohol
    • 2 ml of Mr.T super solvent



    Procedure:


    • measure one gram of powder
    • draw out 2 ml of the Mr. T super solvent using one of the 3 ml syringes
    • place the measured powder in the open vial and add the solvent
    • place the rubber stopper back on the vial and put one of the 20 gauge pins in the stopper
    • place the vial in a small pan and place the pan on the eye of the stove
    • heat until the powder dissolves into a liquid (usually around 239.8-242 degrees F)
    • turn off the heat and let it cool down in the pan to room temperature (approx. 15 minutes)
    • heat the oil in a suitable container in the oven until it reaches a minimum of 212 degrees F to sterilise it (it will be necessary to use slightly more oil than is required as all of it will not be able to be utilised)
    • draw out 0.2 ml of benzyl alcohol (this will account for 1% of the solution so make sure the measurement is correct)
    • add the benzyl alcohol to the solution in the vial and shake very gently
    • draw out the oil with the 10 ml syringe (make sure the oil has cooled down somewhat before doing this)
    • add 15 ml of the oil (saving 2 ml for later) to the solution in the vial and shake very gently Note: If the winstrol begins to clump back up, reheat the solution (place in a pan, put the pan on the eye of the stove and heat until it liquefies again) and allow it to cool down slowly
    • place one of the 18 gauge pins in the sterile, unopened vial and attach the Whatman sterile filter
    • draw out the solution using the other 10 ml syringe, attach to the filter, and slowly press the solution out into the sterile vial
    • use the previously saved 2 ml of oil in the other syringe and run it through the filter to ensure that all the Winstrol passes through
    • after the filtering process, leave the pin in the sterile vial and remove the filter
    • place the vial in a pan and place the pan on the eye of the stove
    • heat for 15-20 minutes, remove from heat, and let it cool down to room temperature (approx. 15 minutes)



    The finished solution will be light-gold in colour.
    Ensure that you follow the guidelines carefully for this conversion.

  3. #3
    Member
    IunitsU's Avatar


    Join Date
    Aug 2018
    Posts
    39

    Thanks Thanks Given 
    0
    Thanks Thanks Received 
    7
    Thanked in
    7 Posts
    Rep Points
    15517526

    Injectable winstrol is strong stuff if made properly. I prefer injectable over oral but only use oral! Its good either way.
    www.PuritySourceLabs.ru

  4. #4
    Board Rep
    BOARD REP
    ALLEX's Avatar


    Join Date
    Dec 2017
    Posts
    1,536

    Thanks Thanks Given 
    3
    Thanks Thanks Received 
    324
    Thanked in
    259 Posts
    Rep Points
    2118684547

    Try 1g of powder and 2.5ml of guaiacol. Add heat until starts smoking. Add castor oil in small amounts bringing to smoke each time. Doesn't really need BA but you can do 1%.

Similar Threads

  1. Winstrol Oil vs Winstrol Water Base
    By gabulldog in forum Anabolic Steroids
    Replies: 5
    Last Post: 08-11-2017, 10:17 PM
  2. Winstrol
    By VTX in forum Anabolic Steroids
    Replies: 9
    Last Post: 06-13-2016, 03:38 AM
  3. winstrol
    By smokedout in forum Anabolic Steroids
    Replies: 11
    Last Post: 02-28-2014, 11:30 PM
  4. Ok guys winstrol dilemna HOW TO MAKE LIQUID WINSTROL
    By tehbeastaxl in forum Research & Homebrew Chemistry
    Replies: 1
    Last Post: 11-02-2013, 05:42 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Copyright© 2012-2018 Anabolic Steroid Forums