Capping

Results 1 to 4 of 4

Thread: Capping

  1. #1
    Senior Member


    Join Date
    Jun 2015
    Posts
    892

    Thanks Thanks Given 
    32
    Thanks Thanks Received 
    65
    Thanked in
    55 Posts
    Rep Points
    2146614842

    Capping

    Hey guys,

    Just picked up "the capsule machine" size 00. The one I purchased and used to cap my DNP sucked ass and I wound up tossing it.

    Anyways just a few clarifications since its been a few months and i seem to have "misread" how to cap.


    1 article states "pestle and mortar" to mix everything thoroughly, i used a ziploc bag and just shook the hell out of it for a good 5 minutes. Since I used DNP in my last batch (200mg per cap) it didnt seem too bad if it was off a few miligrams, but considering the low dosage of SD (10mg caps) is a pestle and mortar really more accurate or a better option?


    Does anyone happen to know off hand what the fill volume of a 00 cap is? Its 113 degrees out and Im not looking forward to filling 24 caps, then dumping them out to weigh it all.


    Finally. I have adex en route. Enough for 2000 .5mg caps. Now I dont need to fill all of them at 1 time, but Im going to go out on a limb and say liquid would be a more efficient route yes?

  2. #2
    Super Moderator
    SUPER MOD
    REHH's Avatar


    Join Date
    Oct 2014
    Posts
    8,096

    Thanks Thanks Given 
    731
    Thanks Thanks Received 
    1,005
    Thanked in
    743 Posts
    Rep Points
    2147483647

    Pestle and mortar is more for crushing and grinding powder than mixing. Plastic baggie is good for mixing. I don't use loading blocks so can't give you advice but micro dosing like adex is probably best made into liquid.

  3. #3
    Senior Member
    Swolewelder's Avatar


    Join Date
    May 2018
    Posts
    439

    Thanks Thanks Given 
    67
    Thanks Thanks Received 
    67
    Thanked in
    55 Posts
    Rep Points
    6700100

    I tried capping GW using a 00 and it was just a shitty experience lol I feel like it is hella innacurate to cut down small mg amounts (20mg GW per cap) and from now on I will make liquid suspensions simply because I feel like it is more accurate... much less time consuming than capping as well.
    When the hood drops, the bullshit stops.

  4. #4
    Member


    Join Date
    Jun 2017
    Posts
    45

    Thanks Thanks Given 
    1
    Thanks Thanks Received 
    2
    Thanked in
    2 Posts
    Rep Points
    200100

    You can buy a cheap food processor ($40 tops) to mix powders pretty accurate up to 10mg a cap I would say. Trying to do .5mg a cap would be pretty hard to get an accurate dose. You can also get a 400 cap press off ebay pretty cheap. 00 seems big as a size 0 cap will hold up to about 500mg.

    For the last question I would think Adex at .5mg would be better in an oral solution.

    - - - Updated - - -

Similar Threads

  1. Capping Orals
    By CompoundLifts31 in forum Research & Homebrew Chemistry
    Replies: 32
    Last Post: 03-06-2018, 05:40 AM
  2. Capping raw DNP
    By Murse32 in forum Purple Panda Labs
    Replies: 9
    Last Post: 06-30-2017, 09:50 AM
  3. Capping DNP
    By Murse32 in forum Research & Homebrew Chemistry
    Replies: 1
    Last Post: 06-18-2017, 10:05 AM
  4. Formula for capping?
    By Nyde in forum Research & Homebrew Chemistry
    Replies: 11
    Last Post: 12-12-2016, 10:56 AM
  5. Capping Machine
    By Montego1 in forum Research & Homebrew Chemistry
    Replies: 11
    Last Post: 04-05-2016, 03:30 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Copyright© 2012-2018 Anabolic Steroid Forums