- Joined
- Dec 24, 2013
- Messages
- 11,512
- Reaction score
- 780
- Points
- 113
No pip and flows like water. You don't feel it go in.Smooth as butter as in no PIP? Wow im getting pretty excited i have to say
No pip and flows like water. You don't feel it go in.
No pip and flows like water. You don't feel it go in.
Actually it is. But she is pinning Lady Primo 50mg/wk split and 10var each day. Lady Primo is just 50mg/ml 10%BB and 50/50 eo/M840. I love this carrier blend. 100%eo is too much, but the M840 adds just enough thickness that slows down the absorption of the EO. It is the perfect slin pin carrier because even with the shallowness of a slin pin it dissipates very evenly. Even subQ it reacts more like a water based compound than oil. My wife has only pinned hgh before so this meant she started pinning herself without questions of technique. It is so gentle a "bad pin" at the doses and volume is unlikely..That's what she said
Curious as to why so much BB when you are using Mig and EO?
Using these solvent like carriers, I have been dropping BB to an absolute minimum, with the help of our mutual friend/savant here.
If you put in too little are you ever able to tell before bottling and add more back in and reheat or are u screwed and have to start over.
This is why you always let new recipes sit at room temperature for 24-36 hrs to see if it holds and also letting the oil cool will give you a dead volume reading to see if you're measurements are correct. Hot oil expands and will throw of your products by several mL if your donot do it right. Most people end up with an overdosed product.. which is ok sometimes..but not when you're dealing with potent compounds with less margin for errors.
If you end up with a perfect volume that is crashing you have to figure out which solvents are best for that specific compoundand then you have no choice but to dilute it down with the chosen solvent(s) so it will hold. You can easily do some math and figure out where the final MG will end up per CC.
This is why you always let new recipes sit at room temperature for 24-36 hrs to see if it holds and also letting the oil cool will give you a dead volume reading to see if you're measurements are correct. Hot oil expands and will throw of your products by several mL if your donot do it right. Most people end up with an overdosed product.. which is ok sometimes..but not when you're dealing with potent compounds with less margin for errors.
If you end up with a perfect volume that is crashing you have to figure out which solvents are best for that specific compoundand then you have no choice but to dilute it down with the chosen solvent(s) so it will hold. You can easily do some math and figure out where the final MG will end up per CC.
If some are crashing and some aren't then something isn't mixed right. That means the vials that crashed have more hormone in them than the others.
Not sure if I read your post correctly but you're doing it backward. Add powders first along with solvents. Heat them until they start to to the melting point.. THEN pour up to your fill line with cold oil. From here.. keep the heat on and stir stir stir stir. Once it's in solution and heated I will set my magnetic stir to medium turn heat off... and I let it stir for 30min until it's cool again
If some are crashing and some aren't then something isn't mixed right. That means the vials that crashed have more hormone in them than the others.
Not sure if I read your post correctly but you're doing it backward. Add powders first along with solvents. Heat them until they start to to the melting point.. THEN pour up to your fill line with cold oil. From here.. keep the heat on and stir stir stir stir. Once it's in solution and heated I will set my magnetic stir to medium turn heat off... and I let it stir for 30min until it's cool again
You made 160mL correcto?
And why add the EO?
Are you using a magnetic stirrir?
A regular rod stirrir won't stir nearly as accurately..
What size beakers are you using?